Panasonic EEU Series Aluminum Electrolytic Capacitors: Complete Selection Guide

Every power supply, every audio amplifier, every industrial control board has at least one radial aluminum electrolytic capacitor on it — and if you check the BOM, there is a good chance the part number starts with EEU. That prefix belongs to Panasonic's radial leaded aluminum electrolytic family, one of the most specified capacitor lines in the world, from consumer adapters to 450 V industrial power stages.

At Geefook, Panasonic electrolytic capacitors are one of our three core supply lines. This guide covers the EEU series range, how to decode the part numbers, and how to pick the right series for your design.

Series Overview: Which EEU Family Fits Your Application

Panasonic groups its radial aluminum electrolytics by temperature rating, lifetime, and impedance. Here is the practical map:

SeriesTemp / LifetimeKey CharacteristicTypical Use
EB-A105 °C, 5,000–10,000 hHigh ripple, high frequencySMPS output, ballasts
ED-A105 °C, 8,000–10,000 hHigh reliabilityLong-life industrial
EE-A105 °C, 8,000–10,000 hHigh ripple, high voltage400–450 V PFC stages
FC-A105 °C, 1,000–5,000 hLow impedanceClassic general purpose
FK-A105 °C, 3,000–5,000 hLow impedanceCompact designs
FM-A105 °C, 2,000–7,000 hVery low impedanceCPU/GPU board-level
FP-A105 °C, 4,000–5,000 hLow impedanceAudio, long life
FR-A105 °C, 3,000–5,000 hLow impedanceHigh-capacity boards
FS-A105 °C, 5,000–10,000 hLow impedance, long lifeLED lighting, adapters
GA-A105 °C, 1,000 hStandardCost-driven designs
KA-A / KS-A85 °C, 1,000 hStandard (KS also in bi-polar)Consumer electronics
TA-A / TP-A125 °C, 2,000–5,000 hAutomotive gradeUnder-hood electronics

Rule of thumb: for new designs at 105 °C, start from EB (high ripple) or FS (long life); for board-level decoupling with tight impedance budgets, FM and FR; for 125 °C automotive, TA or TP.

Decoding the Part Number

Let's break down EEU-EB1E101SH:

  • EEU — product family: radial aluminum electrolytic

  • EB1 — series (EB) and size/generation code (1)

  • E — rated voltage code: E = 25 V

  • 101 — capacitance: 10 × 10¹ = 100 µF

  • SH — terminal/packaging: S = straight leads, H = ammo-pack (B = bulk box, L = long leads)

Voltage Code Table

Code0J1A1C1E1V1H1J1K2A2C2D2E2G2W
V DC6.310162535506380100160200250400450

Capacitance Code

Three digits: first two are significant figures, third is the multiplier in µF — 221 = 220 µF, 471 = 470 µF, 102 = 1,000 µF, 472 = 4,700 µF.

How to Select: Four Numbers That Matter

1. Voltage derating. Run electrolytics at 70–80 % of rated voltage. A 35 V part on a 24 V rail is comfortable; a 25 V part is not.

2. Ripple current. This is the real killer. Check the datasheet ripple rating (mA rms at 100/120 Hz or 105 °C, high frequency) against your circuit's ripple. Undersized ripple current = early failure, regardless of voltage margin.

3. Lifetime. A capacitor rated 10,000 h at 105 °C lives roughly 2× longer for every 10 °C below rating (Arrhenius rule). A 5,000 h part at 65 °C ambient ≈ 40,000 h — but only if ripple heating stays in budget.

4. Case size. Diameter × height and lead pitch (5.0 / 7.5 / 10.0 mm) decide fit. Panasonic's series flow chart maps capacitance + voltage → case size; higher-voltage values jump to 12.5–18 mm cans.

Low-ESR and Automotive Options

Standard series (KA, KS, GA) work for cost-sensitive consumer gear, but switch-mode designs need low-impedance parts. The FC → FK → FM/FR/FS progression trades impedance against lifetime and price. For board-level bulk decoupling near processors and FPGAs, FM-A and FR-A at 6.3–35 V are the usual choices.

For automotive and harsh environments, look for AEC-Q200 qualified order codes — Panasonic marks these in distributor listings (for example, EEU-EB1E101S and EEU-EE2W330S carry AEC-Q200). TA-A (125 °C, 2,000 h) is built for under-hood and LED headlamp drivers; TP-A extends that to 5,000 h.

Bi-polar note: KS-A and KA-A are also available in bipolar versions for audio coupling where DC bias is absent or reversed.

Commonly Ordered EEU Parts

These are the workhorses we ship most often:

  • EEU-EB1E101S — 100 µF, 25 V, EB series, 5 × 11 mm: the default bulk capacitor for 24 V industrial rails

  • EEU-EB1J101 — 100 µF, 63 V, 10,000 h @ 105 °C: long-life 63 V filter

  • EEU-FC1E101S — 100 µF, 25 V, FC low-impedance classic for SMPS output

  • EEU-FR1E471L — 470 µF, 25 V, FR, 9,000 h: board-level bulk decoupling

  • EEU-ED2G470S — 47 µF, 400 V, ED series: PFC and bulk hold-up in high-voltage stages

  • EEU-EE2W330S — 33 µF, 450 V, EE series, high ripple, AEC-Q200: 450 V continuous-duty designs

Browse our full Panasonic line for in-stock EEU values.

Frequently Asked Questions

EEU vs EEE — what's the difference?
EEE is Panasonic's SMD V-chip prefix; EEU is the radial leaded family. Electrically overlapping ranges, physically different packages.

What does the "A" in EB-A / FC-A mean?
The generation suffix. Panasonic has migrated most classic series to "-A" revisions (AEC-Q200-capable constructions, RoHS-compliant); order codes stayed compatible.

Can I use a 105 °C part at 125 °C?
No. Temperature rating is a hard limit. Above 105 °C use TA-A or TP-A (125 °C rated).

Are Panasonic electrolytics still in production?
Yes — the radial families above are active, with the "-A" revisions current. Always confirm the exact order code against Panasonic's latest datasheet before finalizing a BOM.

In Stock at Geefook

Geefook is an independent distributor of Panasonic electronic components. We carry the EEU radial range in depth — high-runners like EEU-EB1E101S, long-life EB/ED/EE values, and low-impedance FC/FR/FM parts — with:

  • Real-time stock and competitive pricing on the full BOM

  • Same-day dispatch from Hong Kong

  • Full incoming inspection (visual + sampling on request)

Request a quote: send your BOM to sales@geefook.com, or submit an inquiry online — replies within hours, not days.

Series data per Panasonic radial lead type catalog (2023 revision). Always confirm specifications against the latest datasheet for your exact part number.